Plug your laptop into an outlet. The factory reset process may take a while, and losing power in the middle can cause serious problems. Make sure it's plugged in before continuing. Reboot your computer and press. You may need to press the keys a couple times in order for them to register. This will load the Recovery Manager. If prompted by the Windows Boot menu, press Enter. You will be asked several times to confirm that you want to proceed. Starting the restore will erase all of the data on the disk and then reinstall Windows and the programs that came with your laptop.
The restore process can take up to an hour to complete. There's an option to keep user data and restore the computer, but this is not recommended on the chance that some of that data is what's causing the computer to not work properly. Create your account and start using your computer. Once the restore process is complete, the laptop will act as if it has been turned on for the first time after you purchased it.
You will be prompted to create a Windows account and configure your personal settings. I can't access the Recovery Manager. If you've previously formatted the hard drive, or have installed a new hard drive, you won't have the recovery partition anymore. You'll need to use a recovery disc, or a Windows installation disc in order to wipe the computer and reinstall Windows.
See the next section for instructions on using one of these discs. Restoring the computer doesn't fix the problem. If you've completely wiped the laptop and reinstalled Windows using the factory reset process and the problem still isn't gone, the cause is likely a hardware component.
Installing a new hard drive or installing new RAM are both fairly straightforward processes, and may be able to fix your problem. You may need to contact Gateway for factory service if these don't help. Part 4. Locate your recovery disc if possible. Laptops often require a variety of specific drivers, and using the recovery disc is the easiest way to make sure that these get reinstalled when you reset your laptop. If you can't use the Recovery Manager because the recovery partition is gone, try to use the recovery disc.
You can order new recovery discs from Gateway. Find or create a Windows installation disc if you can't get a recovery disc. If you don't have a recovery disc for your laptop, you can use a Windows installation disc to wipe and restore your laptop. You will need a disc for the same version of Windows that's currently installed. If you're using Windows 7 and have a valid product key, you can create a disc here. If you're using Windows 8 and have a valid product key, you can create a disc here.
Reboot your computer and repeatedly press F For Gateways, this is will open the Boot Menu. Repeatedly press this key as soon as the Gateway or Acer logo.
Change the boot order. In order to use a recovery disc or install Windows from the disc, you'll need to set your computer to boot from the disc drive before the hard drive. The Boot Menu will allow you to change the boot order. Save your settings and reboot. Make sure that the Windows installation disc or USB drive is inserted. Press a key when prompted. This will start either the Recovery Manager if you are using a recovery disc, or it will start the Windows setup process if you are using a Windows installation disc.
If you are using the Recovery Manager, refer to the previous section for instructions on restoring your laptop. If you are using a Windows setup disc, read on. Set your language preferences and choose to "Install Windows" or "Install now".
The installation process will erase all of the data on the hard drive and start from scratch. Select "Custom advanced " installation if prompted. This will allow you to ensure that everything has been deleted. Delete any partitions. When asked to choose where you want to install Windows, you will be shown all of the partitions on your hard drive.
Select each partition and click "Delete". This will delete all of the data on the partition. Select the single remaining partition as the destination for the installation.
The installer will automatically format it to the correct file system and begin installing the Windows files. Wait for the installation to complete. The Windows installation process usually takes around a half hour to complete. You can monitor the progress on the screen. Finish the installation and enter your product key. After installation is complete, you will be prompted to enter your Windows product key. Your search comes to an end if you are looking for how to factory reset Windows XP without password.
The method is a little tricky but carefully follows the article guideline to successfully implement it on your Windows. Choose the first one and it will immediately display you the operating system that you are currently using. Wait for the operation to be completed, first, it will check the corrupt files and system issues.
Only try this method if you have already done this before or know much about system files otherwise use the below methods.
Basically, Safe Mode deactivates all the services and programs to allow you to troubleshoot your operating system. Let Windows do his tasks and in the meanwhile, you have to do nothing but wait for the process to end. Click on that account. The Windows by default admin account will appear through which you can do the factory reset process. Edit this Article.
We use cookies to make wikiHow great. By using our site, you agree to our cookie policy. Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article methods. Tips and Warnings. Related Articles. Author Info Last Updated: September 16, Method 1.
Select the radio button next to the restore point for which you want your computer restored. You can either choose the restore point recommended by Windows, or choose a different restore point.
Method 2. Click on the Start menu, then click on the arrow next to the Lock icon. Click on the name of the operating system you want repaired. Select the restoration point to which you want your computer restored. Method 3. Power on your Windows Vista computer. Press the F8 key repeatedly as your computer boots up.
The Advanced Boot Options menu will display on-screen. If the Advanced Boot Options menu does not display, restart your computer and continue to press F8 repeatedly before the Windows logo displays on-screen. Select your username from the dropdown menu and type your Windows Vista password. Choose the restoration point to which you want the state of your computer restored.
Method 4. Insert your Windows Vista Installation disc into the disc drive of your computer. Method 5. Disconnect all non-essential external peripherals from your computer.
0コメント